Nilight Headlight Assembly for 1999 2000 2001 2002 Chevy Silverado 1500 1500HD 2500 2500HD 3500 Chevrolet Tahoe Suburban Replacement Headlamp Housing Bumper Lights Set

Arrived this morning and installed this morning. 2003 Chevy Tahoe. Easy install, takes about 20 minutes total to remove the old and install the new. Crystal clear, very bright with my Sylvania ZXE Gold bulbs, beautiful transformation, really improves the look of my truck, perfect fitment, no gaps anywhere, tight fit. I would definitely recommend these light assemblies to anyone needing some great lights and if ever needed I would definitely buy them again. Tips: Before installation, adjust the up/down screws in until they are about 1/2 an inch long, they are set too far back from the factory and will make it seem as though they aren't going to fit. Disconnect your bulbs and place the bulbs in the assembly then, connect your harness back up, the low beam bulb fitment is very tight and will be hard to connect with the harness on. Be sure to check daytime running and signal assembly and make sure you have the correct lights for the side that you are getting ready to put on, they will fit bavkwards but you'll notice it's really tight and will have a bad gap (Ask me how I know😂) Overall I am 200% satisfied with this purchase. The fog lights were purchased 2 years ago from Topscope, they still look great and perform great.

They look very great and are fast and easy to assemble on your own. They function perfectly and the lights looks brighter than usual.

Terrible product, this things didn’t fit right . Had to make extra holes to make headlights fit ok and still they look uneven and can’t adjust, because the adjusting mechanism does not work . The parking lights keep on popping out . A total waste of money .

Looks great, easy installation, fair price.

Typical fast Amazon shipping, great packaging. Lights look great and fit well with small alteration. The headlight bulbs themselves are a VERY tight fit, I used a bit of spray silicon on my finger and wiped the 'O' ring and where it twists into the housing. The left-hand park lamp has two 'tits' that press against the mounting panel, and they seemed to be about 3/16" to long, I used a grinder and then they snapped right in place. The lens are crystal clear and the reflectors seem to be high quality. Be careful, the black mounting panels are thin plastic and would break easy, a little lube is your friend!

Very quality headlight they look fantastic on my 01 Chevy Ease of installation: Very easy to install no tools required

Style yes looks great and as a whole assembly yes its the right assembly. BUT, the socket hold downs were not correct. All the ratings about condensation is because the lower lights are not oem thickness at all the socket holes, one in particular can't remember which one maybe side marker is too thin to hold down the bulb socket/connector tight. The main thing was the headlights, the hold down was not correct, OE bulbs were loose, I had to shave the screw towers for a proper fit. installing LED bulbs HIGH and Low, oddly enough the Low beams were pretty good, i think i shaved one of the 2 for tightness. Both L/R Highbeams for LED's were not correct i had to shave both sides for fit and had to rotate the hold down for it it to be correct LED alignment. I purchased amazon LED's, so that was an initial factor but I did put them in my old assembly and they fit perfect and aligned straight. (LED's (especially headlights) are very specific when being aligned. up/down like the initial would have been worthless, side to side to match the headlights reflection surfaces is ideal...and was achieved. kinda id say 95%, with fabrication. There is a lock point but no matter how I could change the hold down orientation it did not create perfect alignment. Had to on both sides rotate back from lock position maybe 10 to 5 degrees from lock to be perfect.) SO good fit for your body, great style, but terrible connector fit, I've gotten it to work but it made a 30 min change a 3 hr retrofit for it to be perfect. Great deal and no telling if others will be any better to the points I found, but for sure these needs some help to be perfect especially with LED's. Not so much an issue with halogen but the tightness would be a concern for sure. i've added a a video sorry for the shakiness 2 hands and 3 objects lol, thought i had taken photos to show the alignment issues, but essentially it would have should the 2 sided LED's pointed up and down towards no reflective surfaces while side to side is the way to go so the light actually hit mirrors. ***To be clear my stock assemblies allowed that perfect alignment and were tight with each LED. So I would not say exact fit or complete ease of installation if you are expecting it to be 100% correct. The lack of tightness is for sure a concern for the longevity of your halogen bulbs.

great

Los faros se ven de calidad sencilla, pero en cuanto a el funcionamiento alumbran muy bien